Polk Audio PA D4000.4


Compare

PA D4000.4

Super Efficient Class D Bridgeable 4-Channel Mobile Audio Amplifier

  • Low THD, a high signal-to-noise ratio, plus wide bandwidth frequencies make the PA D4000.4 four-channel a superior choice for distortion-free power
  • Super-efficient class D design—Runs much cooler than conventional amps
  • High-speed MOSFET—Switching power supply
  • Toroidal transformers help keep the amplifier’s sleek design under 2-inch tall while ensuring plenty of clean, efficient power.

PA D4000.4

The PA D4000.4 amplifier is capable of bridging two full-range channels into a single full range channel with higher output power. For instance, one front and one rear channel will increase the output power from 125W per channel to 400W per channel (for a 4 ohm load). The most common hookups for the PA D4000.4 would be four full-range channels, two full-range channels and a bridged sub, or two bridged subwoofers.

OVERALL

  • Total Pieces
    1

ACCESSORIES

  • Included Accessories
    • (4) Phillips Screws
    • (1) Terminal Block Adaptor

SHIPPING CARTONS

  • Carton 1

WARRANTY

  • Standard Warranty (When purchased from an Authorized Dealer)
    1 Year
  • Warranty When Bought from and Installed by an Authorized Dealer
    2 Years

AMPLIFIER

  • Total Pieces
    1
  • Height
    1.813″ (4.6 cm)
  • Width
    10.938″ (27.78 cm)
  • Depth
    6.75″ (17.15 cm)
  • Weight
    5 lbs (2.27 kg)
  • RMS Continuous Power @ 4 Ohms
    125 W x 4
  • RMS Continuous Power @ 2 Ohms
    200 W x 4
  • Power Bridged @ 4 Ohms
    400 W x 2
  • Distortion at Rated Power
    <0.1%
  • Minimum Impedance Bridged
    4 Ohms
  • Minimum Impedance Not Bridged
    2 Ohms
  • Signal-to-noise Ratio
    105 dB
  • Frequency Response
    20 Hz-20 kHz
  • Damping Factor
    >100
  • Crossover Filter Slope (dB/octave)
    12 dB/octave
  • Filter Switch (Front)
    3-position (HPF, Full, BPF)
  • High Pass Filter Frequency Range (Front)
    20 Hz – 4 kHz
  • Low Pass Filter Frequency Range (Front)
    50 Hz – 5 kHz
  • Front Gain Control
    200 mV – 6 V
  • Filter Switch (Rear)
    3-position (HPF, Full, BPF)
  • High Pass Filter Frequency Range (Rear)
    20 Hz – 4 kHz
  • Low Pass Filter Frequency Range (Rear)
    50 Hz – 5 kHz
  • Rear Gain Control
    200 mV – 6 V
  • Line Level Inputs (Y/N)
    Yes
  • Line Level Outputs (Y/N)
    No
  • LED Power Indicator
    Yes
  • LED Protection Indicator
    Yes
  • Supply Voltage
    10 V – 16 V
  • Fusing & Power/Type
    (1) 40A (1) 35A ATC
  • Power Connections
    4 AWG
  • Ground Connections
    4 AWG
  • Speaker Connections
    12 AWG

INTERNAL AMPLIFIER

  • Channels
    4
  • Amplifier Class
    Bridgeable Class D MOSFET

Key Features

Super-Eefficient Class D Design

Runs much cooler than conventional amps.

Toroidal Transformers

Help keep the amplifier’s sleek design under 2″ tall while ensuring plenty of clean, efficient power

Protection

Thermal, DC offset, reverse DC voltage and short circuit protection

Nickel-plated wire terminals & RCA connectors

Ensure maximum signal transfer

Front & rear level controls

Adjust the gain of the front and rear channels to match the output voltage from your head unit.

Low-pass & high-pass frequency controls

Enables you to adjust crossover overlap for better blending of speakers.

Front & rear BPF, FULL, HPF switches

Selects full range, high pass filter, or bandpass filter to dial in your speaker blending.

Channel mode switch (ST/4Ch)

In the stereo position, the amplifier will send the same signal to front and rear channels.

Stainless steel hardware

Used throughout, it won’t corrode in humid environments

Category: Tag:

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Polk Audio PA D4000.4”

There are no reviews yet.